Athletics - Discus

 

• 

• TDS75 Discus cage to IAAF standard

• Features: Eight post cage with netting suspended 500mm away from the posts. Netting is 5.5m high, knotted mesh 3mm x 44mm square. The net is attached to rail supports which are raised and lowered from each post by rope and pulleys. Each pole has vertical net retaining ropes. Galvanised finish.

1.   

2. TDS72 Discus cage - club standard 

3. Netting is 5.0m high, knotted mesh 3mm x 44mm square. Hot dip galvanised finish. The netting covers the safety zones specified by IAAF.
4. Features: Seven post cage with netting suspended 500mm away from the posts

•  

• TDS90 Multi purpose trolley

• Holds 6 hammers, 6 shots and 12 discus

1. 

2. TDS85 Discus trolley

3. Holds 24 discus in two rows. (Seen in right of photo)

 

• 

• TDS30 Discus circle

• Circle, 2.5m diameter, made from 75 x 6mm steel and constructed in two halves, re-inforcing rods keep the circle in shape, galvanised and coated white.

1.  

2. TDS35 Portable Discus circle

3. Circle, 2.5m diameter, made from 26mm steel in two halves. White finish   

Athletics - Hammer

• 

• THM85 IAAF Approved Hammer cage

• Features: Ten pole support frame with net rail. Seven metre netting around the perimeter, 10m gate extension panels and 10m x 2m gates. Designed for single circle use with conversion insert.
  
  Netting is 5mm braided with 44mm mesh size. Ground cages with footing spigots are used to locate the poles plus ground anchors in front of each pole are used for net retaining ropes.
  
  The cage covers the safety zones as required by IAAF. Suitable for competition levels up to State Championship.

 

1. 

2. THM80 Hammer cage

3. Features: Eight pole support frame with net rail. Seven metre netting around the perimeter and 9m x 3m gates .Designed for single circle use with conversion insert. Netting is 4mm knotted with 44mm mesh size. Ground cages with footing spigots are used to locate the poles plus ground anchors in front of each pole are used for net retaining ropes. The cage covers the safety zones as required by IAAF. Suitable for competition levels up to State Championship.
   
   Note: Cages for other levels of competition are available.

•  

• THM20 Hammer circle

• Circle, 2.5m diameter, made from 75 x 6mm steel and constructed in two halves, re-inforcing rods keep the circle in shape, galvanised and coated white. Note: This size circle is to be used in conjunction with a conversion circle for hammer use. Alternatively, order 2.135m size for hammer use only.

1. 

2. THM25 Hammer conversion circle

3. Eight piece circle converting 2.5m circle to 2.135m dia for hammer use. Made from all weather synthetic material 20mm thick.

•  

• THM90 Hammer trolley

• Holds 12 hammers in two rows. 

Athletics - Shot Put / Javelin

1. 

2. TSP30 Shot put circle

3. Circle, 2.135m diameter, made from 75 x 6mm steel, reinforcing rods keep the circle in shape, galvanised and coated white.

 

• 

• TSP90 Shot trolley

• Holds 12 shots in two rows. (Left) 

• TJV90 Javelin trolley

• Holds 24 javelins. (Middle) 

• TDS85 Discus trolley

• Holds 24 discus in two rows. (Right)  

1. 

2. TSP35 Toe board

3. Wooden toe board made from hardwood with anchor bolt holes.

•  

• TSP40 Toe plate

• Steel toe plate with ground spikes. White finish

Athletics - Hurdles

1. 

2. THD25 Little "A" hurdle

3. Fixed hurdle with height adjustment from 45-76cm. Wooden batten with rounded edges. Made from 25mm square steel.

• 

• THD26 Little "A" collapsable hurdle

• Hinged hurdle with height adjustment from 45-76cm. Wooden batten with
•                                    rounded edges.

1. 

2. THD30 School hurdle

3. Similar to THD35 but with galvanised crossbar arms and heights from 76-99cm. Steel frame with wooden crossbar.

• 

• THD35 Club hurdle

• Five height positions from 76-108cm. Steel frame with wooden crossbar.

1. 

2. THD50 Olympic weighted hurdle - manual

3. There are five height settings ranging from 79-108cm. Each leg has a counter weight and is manually adjusted by the lever on the side.

• 

• TSC40 3.96m Steeple chase hurdle

• Height adjustable steel beam supports, galvanised finish, 3.96m long timber beam.
  For replacement beams order TSC10.

• TSC50 5.0m Steeple chase hurdle

• Height adjustable steel beam supports, galvanised finish, 5.0m long timber beam.
  For replacement beams order TSC15.  

1.  

2. TSC60 Water jump hurdle

3. The hurdle consists of two height adjustable steel beam supports, hurdle beam, four steel ground sleeves and a steel ground platform which covers part of the water ditch. Galvanised finish. Track surface is applied to the ground platform by the customer.

•  

• THD75 Olympic hurdle cart

• Holds 25 Olympic or Club size hurdles. The tow bar has a plate to connect to electric vehicles or can be supplied with ball joint coupling. Pneumatic wheels and castors, galvanised finish. This cart can be custom made to suit the customer's existing hurdles.

1.  

2. THD65 Little "A" hurdle cart

3. Holds 30 Little "A" size hurdles. The tow bar has a plate to connect to electric vehicles plus a hand tow bar. Wheels are 300mm diameter with roller bearings. This cart is made at the time of order to suit the type of hurdle it will be carrying.

Athletics - Long / Triple Jump

•  

• TLJ05 Track installation trough

• Steel trough 300mm wide, when installed in the ground it is used to contain the long and triple jump take-off
•                                     and toe boards.

1.  

2. TLJ15 Blank trough insert

3. Steel tray 300mm wide with adjustable legs. Track surface material is glued to the tray and placed into the installation trough when not in use.

•  

• TLJ22 Take-off tray and boards

• Steel tray 300mm wide and contains the fine grain ply take-off and toe boards with rubber textured surface, adjustable legs.

1.  
2.  

3. TLJ25 Take-off board

4. Take-off boards 200 x 75mm hard wood painted white.

5. TLJ30 Toe board

6. Toe boards 100 x 75mm hard wood painted red. Install directly in ground..

•  

• TLJ95 Tape measure rod

• A "walking stick" shaped rod with a pointed end to hold the tape measure in the sand pit. 

 

1. TLJ85 Sand leveller

2. A weighted steel bar with handle and cable both ends for levelling the sand pit.  

Athletics - Pole Vault

• 

• TPV55 Scoreboard, 8 digit

• Scoreboard on wheels and has two rows of four digits. Can be made to suit the customers own digits or digit boxes with adjustable levers.
  
  Digit box available in black and red.

1. 

2. TPV60 Pole Vault stand

3. 75mm square crossbar supports with sliding extension arms. Adjustment by hand tool with a moving height gauge at eye level. Suitable for top level competition. Painted finish.

• 

• TPV40 Pole rack without roof

•  Holds 10 x vaulting poles

 

1. 

2. TPV50 Vaulting pole tree

3. A 1.2m high stand with eight arms. Used to support one end of the vaulting pole while athletes are practising. 

Athletics - High Jump

• 

• THJ30 Mat cover on wheels

• Steel framed mat cover with colorbond cladding, 6.0m x 3.3m x 1.2m. Tilt a door opening one end, four x 400mm dia pneumatic wheels, galvanised steel frame, supplied in kit form, no sharp edges, choice of colours, assembled on site. Different sizes available.

1. 

2. THJ55 Mat trolley 3 x 1.2m

3. Trolley with sheet steel top coverd with carpet. Pneumatic wheels and castors, tow-bar for hand or electric vehicle, 3m x 1.2m wide, can carry hurdles or high jump mats, galvanised finish.

4. THJ50 Mat trolley 3 x 1.6m

5. Same as THJ55 but 1.6m wide. 

 

• 

• THJ70 Stand, weighted base

• Stand to support the high jump crossbar, 35mm sq posts with sliding arm, freestanding base frame, galvanised finish.

1.  

2. THJ75 Stand, ground spikes

3. Stand to support the crossbar, 35mm sq posts with sliding arm, spiked base frame, galvanised finish.

• 

• THJ80 High jump stand

• Top of the range stand, 65mm sq posts with sliding arm, freestanding base, painted finish.

1. 

2. THJ10 High jump display unit

3.  

 

Athletics - Track & Field

1. 

2. TRN25 Starters stand

3. Elevated stand with 600 x 600mm platform plus step.

4. TRN26 Starters stand

5. Similar stand as TRN25 but has sides enclosed in a frame, mesh surounding the platform, loud speaker support arm and items tray. Suitable for top level competition. 

•  

• TRN35 Timers stand with roof

• Eight person stand with one level per person. Can also be supplied without the roof (TRN30). Wheels are mounted on the back legs.
• TRN35 Timers stand with roof

1. 

2. TRN10 Lap counter

3. Two digit lap counter on wheels, height adjustable, includes bell.
   
   Choice of digits, TMS30 enclosed case type or TMS32 sliding panel style.

• 

• TMS30 Digit

• Enclosed case with levers.

1. 

2. TMS32 Digit

3. Sliding panels.

• 

• TMS55 Wind sock

• Stand 1.5m high with weighted base and brightly coloured wind sock, coated finish.

1. 

2. TRN20 Starting block cart

3. Holds 10 full size starting blocks. The trolley has two wheels and two castors plus a tow handle. It can also be made for smaller size starting blocks.

• 

• TMS92 Pigtail rope guides

• Steel rope support rods with spiked base, accepts rope up to 12mm dia, painted finish.

1. 

2. TRN40 Lane barrier gates

3. Boom arm 1.2m high which pivots in a ground sleeve and can be made to span one, two or three lanes.

• 

• TMS90 Winners Podium

• Podium with three platform heights, made from steel section with carpeted floors, available in several sizes from one to eight persons per platform, galvanised materials with coated finish.

1. 

2. TMS40 Training weight sled

3. Steel Sled with a central peg which accepts weight lifting weights. Hook attachment for harness. Painted finish.